Use this steel weight calculator to find the theoretical weight of steel plate, round bar, square bar, hex bar, tube, pipe and angle in kilograms, pounds and tons. Enter the size, length and quantity, add a safety allowance, and get a planning weight rounded up for ordering, shipping and lifting estimates.
Choose the shape you are working with, then the material and your preferred unit system. Enter the cross-section dimensions (the fields change with the shape), the length of each piece and how many pieces you need. If you buy steel by weight, add your price per kilogram or pound. Press the button or hit Enter and you will see the weight per metre or foot, the weight of one piece, the total for all pieces, and a planning total that includes your chosen allowance. The diagram above redraws with your dimensions, and two comparison tables show the same part in other materials and at other quantities.
Steel is sold, shipped and lifted by weight, so getting the number right early saves money and prevents hazards. A fabricator quoting a job needs the weight of every bar and plate to price material. A trucker needs to know whether a bundle stays under the payload limit. A rigger needs to know whether a plate is a two-person carry or a crane lift. A single 1,200 × 2,400 × 10 mm plate weighs about 226 kg (498 lb), far beyond what two people should handle by hand. A bundle of fifty 25 mm round bars, each 6 metres long, weighs roughly 1,155 kg before you add the strapping and dunnage.
Homeowners and builders use the same maths when planning a steel beam delivery, a garage lintel, a gate frame or a workshop mezzanine. Estimators use it to compare carbon steel with stainless, where the extra density and the much higher price per kilogram make a real difference. Scrap yards and recyclers use theoretical weights to sanity-check scale tickets. In every case, a quick and consistent calculation beats guessing, and rounding up is safer than rounding down.
This calculator uses the standard theoretical-weight rule of thumb used by mills and suppliers: weight = cross-section area × length × density. Carbon steel is taken as 7,850 kg/m³, which is 0.2836 lb/in³ or about 490 lb/ft³. The result is a nominal, theoretical weight. It is not a certified mill weight under ASTM A6 or EN 10029, and tolerance rules and local codes vary.
Cross-section areas used:
A = width × thicknessA = π/4 × d² (in millimetres this gives the familiar d²/162 kg per metre)A = a²A = (√3/2) × across-flats²A = π × t × (OD − t)A = W×H − (W−2t)(H−2t)A = t × (A + B − t)Tube corner radii and angle root fillets are ignored, which changes weight by only a small percentage. Weight per metre is A × density. The piece weight multiplies by length, and the total multiplies by quantity. The planning total adds your allowance percentage and is rounded up, never down, so the figure errs on the heavy side. Imperial results convert using 1 kg = 2.2046 lb and 1 m = 3.2808 ft. A useful check for plate: steel weighs 7.85 kg per square metre for every millimetre of thickness, or 40.8 lb per square foot for every inch.
Take one carbon steel plate, 1,200 mm wide, 10 mm thick and 2.4 m long, with the default 5% allowance.
If steel costs 1.10 per kg, the estimated material cost is 237.39 × 1.10 = 261.13 (rounded up). Use the 237.39 kg figure when planning handling and transport, and the 226.08 kg figure as the nominal weight.
Multiply width × thickness × length to get volume, then multiply by 7,850 kg/m³. For quick estimates, use 7.85 kg per square metre per millimetre of thickness, or 40.8 lb per square foot per inch of thickness.
Carbon steel is normally taken as 7,850 kg/m³ (0.2836 lb/in³). Stainless grades are a little heavier, about 7,700 to 8,000 kg/m³ depending on the alloy, and gray cast iron is lighter at roughly 7,200 kg/m³.
In millimetres, weight per metre in kilograms is about diameter² ÷ 162. A 25 mm bar is 625 ÷ 162, or roughly 3.85 kg per metre. This calculator uses the exact π/4 × d² area and your chosen density.
Real steel varies from nominal size, and coatings, welds and fittings add weight. The allowance gives you a safer planning number, and the final figure is rounded up rather than down.
No, treat it as an estimate only. Lifting plans must use certified weights, include the weight of rigging and attachments, and be approved by a qualified rigger or engineer under the rules that apply where you work.
Yes. Pick stainless 304, 316 or 430 or gray cast iron from the material list, or enter a custom density in kg/m³ for any other alloy. The comparison table shows how the same part weighs in each material.
Calculator by Toolwick