Roof Overhang Calculator

</> Embed this calculator on your site

This free roof overhang calculator turns your building size, roof pitch and overhang depth into the numbers you actually frame with: rafter tail length, vertical drop, full rafter length, plumb cut, fascia, soffit and the extra roof area the overhang adds.

Roof eave cross-section showing overhang, drop and pitch
Eave cross-section (gable roof). Diagram is not to scale and updates when you calculate.
Wall to wall, across the roof (perpendicular to the ridge).
Along the ridge, between gable walls.
0:1212:1224:12
Horizontal distance from wall face to tail.
Gable-end overhang. Enter 0 for none.
Used only for a setback warning.

Estimates only. By using this calculator you agree to our Terms.

</> Embed this calculator on your site

Free for any website, blog, classroom or intranet. No sign-up, no ads inside the embed. Copy the code and paste it into your page.

Preview the embed

How to Use This Roof Overhang Calculator

Enter the building width (wall to wall, across the roof) and length, drag the slider to your roof pitch, then type the eave overhang and rake overhang in inches. Pick your rafter size so the plumb cut and birdsmouth limit can be worked out. Press Calculate, or hit Enter in any field. You get the full rafter length with overhang, the rafter tail, the vertical drop, fascia and soffit quantities, and a comparison table of other eave depths at your pitch. The diagram redraws with your values.

Why This Matters

Overhang looks like a small detail, but it does real work. A 12 to 24 inch eave keeps rain off siding, windows and the foundation line, which is where most moisture damage starts. A deeper overhang also shades south-facing glass in summer, when the sun is high, and still lets low winter sun in. Builders in hot, sunny climates often go to 24 inches or more, while 12 inches is common in cold, snowy areas where long tails collect ice and snow.

The number also drives money and safety. Take a 24 × 36 ft house with a 6:12 roof and 12 inch rakes. Going from a 12 inch to a 24 inch eave adds about 85 square feet of roof (two eave sides, each 38 ft long and 1 ft wider, times the 1.118 slope factor). That is a bit under one extra square of shingles, plus longer soffit runs. If you deepen the rakes to 24 inches as well, the total added is closer to 147 square feet. Longer tails are also more exposed to wind uplift and snow load. Work out the sloped length, the drop and the stock size before you buy: a rafter that finishes at 14 ft 6½ in cannot be cut from a 14 ft board, so you need 16 ft lumber and the right plan for the waste.

How It's Calculated

Overhang is measured horizontally, but rafters run along the slope. The calculator converts using the slope factor from the pitch (rise per 12 in of run):

Eave fascia is two runs of the length plus both rake overhangs. Rake fascia is four sloped runs from tail to ridge. Eave soffit area is the level soffit width times the same eave length. Ridge board thickness, birdsmouth seat, wall thickness and fascia thickness are not subtracted, so lengths err on the long side.

Results that affect what you buy or cut are rounded conservatively. Rafter lengths round up to the next ⅛ inch, lumber rounds up to the next even foot, material quantities round up to whole feet or square feet, and the birdsmouth seat limit (about one quarter of the rafter depth, a common IRC R802 rule of thumb) rounds down. The warnings reference IRC R802 (roof framing) and R302.1 (fire separation) as general guidance only. Local codes, snow and wind loads vary.

Worked Example

A 24 ft wide by 36 ft long house, 6:12 pitch, 12 in eave and rake overhangs, 2×8 rafters:

Tips & Common Mistakes

Frequently Asked Questions

How much roof overhang should I have?

Most homes have 12 to 24 inches on the eaves and about 6 to 12 inches on the rakes. Wetter and sunnier climates benefit from deeper eaves. Snowy regions often stay shorter because long tails collect ice dams and snow load.

How do you calculate roof overhang length?

Measure the horizontal distance from the outside wall face to the end of the tail, then multiply by the slope factor, √(144 + pitch²) ÷ 12, to get the length along the rafter. This calculator does both and also gives the vertical drop.

What is the maximum roof overhang without extra support?

A common rule of thumb is about 24 inches for ordinary rafters. Many span tables assume that figure. Longer overhangs usually need lookouts, larger rafters or an engineer's design, and a good guide is no more than a third of the backspan.

Does overhang affect how much roofing I need?

Yes. Overhang adds surface on every side. The comparison table shows how much extra roof each eave depth creates at your pitch, holding your rake overhang constant. Add waste, usually 10 to 15 percent, on top of the area shown.

Is the overhang measured to the fascia or the rafter tail?

Most framers measure to the plumb cut at the end of the rafter tail. The fascia board adds about 3/4 to 1½ inch beyond it. If you want a specific finished overhang, subtract the fascia thickness before entering the value.

Can I build an overhang near my property line?

Often not freely. Building codes such as IRC R302.1 can restrict projections within about 5 feet of a lot line, require a fire-rated underside, or prohibit them within 2 feet. Check with your local building department before framing.

Related Tools